Hotline:+86 19182170296
E-mail:sales@cdjy1.cn
Overview of electric retractable gate installation
- Categories:Frequently Asked Questions
- Author:
- Origin:
- Time of issue:2020-09-07
- Views:0
(Summary description)When you received the "big thing" of the electric retractable gate, did you feel that it was impossible to install it? Then let the editor teach you how to install the electric retractable gate step by step.
Overview of electric retractable gate installation
(Summary description)When you received the "big thing" of the electric retractable gate, did you feel that it was impossible to install it? Then let the editor teach you how to install the electric retractable gate step by step.
- Categories:Frequently Asked Questions
- Author:
- Origin:
- Time of issue:2020-09-07
- Views:0
When you received the "big thing" of the electric retractable gate, did you feel that it was impossible to install it? Then let the editor teach you how to install the electric retractable gate step by step.
The first step: first remove a wooden strip from the end of the machine head, and then pull the gate row out of the wooden box.
Step 2: After pulling it out, find the key of the machine head. Generally, the key of the machine head is tied up with a bandage on the movable round tube of the cross bar at the end of the gate row.
Step 3: Use the key to open the head cover and take out the white box next to the motor. There are wireless remote control*2, wireless station control*1, and clutch key*1 inside.
The fourth step: The function of the wireless remote control is to control the operation of the retractable gate, which is compact and easy to carry. The console is used in the guard room to facilitate the daily operations of security personnel.
Step 5: If the "gear rotates but the shaft does not rotate" situation occurs when the gate is operated by remote control, it means that the motor clutch is not closed. Insert the hexagonal clutch key in the box into the shaft of the motor binding chain. There is a hexagonal groove recessed inward at the end of the shaft. Insert the clutch key and turn it 180 degrees to open the clutch.
Step 6: After the motor is debugged, close the gate row against the wall (the position where the gate body needs to be fixed). There are three fixed positions at the end of the gate body. The first one is the horizontal square tube in the middle of the gate row. , Can be fixed on the wall. There is a horizontal square tube at the bottom of the end of the gate row, and two stainless steel corners on the left and right ends of the inside, which can fix the gate on the ground (suitable for installation sites without wall posts).
Step 7: After the gate body is folded against the wall, the center of the gate body shall prevail (i.e. if the width of your gate is 80 cm, the circular magnet is installed at the position of 40 cm). The middle part of the row is buried with a circular magnet every 20~25 cm along a straight line (Note that: when the magnet is buried, all the magnets, including the square magnet, need to be buried on one pole face [ie: the first magnet If it is buried to attract the same sex, the magnets installed later also need to be buried to attract the same sex])
Step 8: After burying the round magnet, bury a square magnet (to control the gate limit) directly below the stop position of the nose when the gate is closed (corresponding to the placement of the black clip [limit navigator] at the bottom of the nose) stop)
Step 9: After the gate body is fully extended, within 30~100mm from the front of the machine head after fully unfolded (that is, the part that needs to be parked at a distance of 30~100 cm) and the docking part of the machine head Just bury a square magnet directly below.
Step 10: Place a square magnet on the bottom of the machine head (corresponding to the white tube [infrared reed tube]) 150mn away from the round magnet (the middle part of the track) at a position about 1000mm away from the closed gate and the wall. (As long as the gate is approaching the end, it will return without obstruction. Note: [The retractable gate equipped with infrared anti-collision can only be fixed with the infrared magnet to prevent the gate from automatically shrinking during the closing process])
Eleventh step: The voltage of 220V power supply (2.5 square hatchback) should not be lower than 180V. The three power lines correspond to red (live wire), yellow (ground wire), and blue (zero wire). After connecting the three wires (the ground wire may not be connected), you are done!
Scan the QR code to read on your phone
CONTACT
Phone:+86 19182170296
Add:No. 63-69, Section 2, Huajin Avenue, Qingbaijiang District, Chengdu
E-mail:sales@cdjy1.cn
Web:en.cdjy1.cn
Copyright © 2020 Chengdu Jieying Intelligent Technology Co., Ltd. 蜀ICP备19011659号